Graphics, Figures & Tables ⇒ pst-plot package

[workerbee]

Hi,

So I'm trying to draw a graph within Latex using the pst-plot package but I'm having trouble in a very odd place.

Here's my coding:

Code: Select all

Code, edit and compile here:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
\documentclass[11pt]{book}
\usepackage{pst-plot}
\usepackage{pstricks}
\begin{document}
\psset{unit=2cm}
\begin{pspicture}(-2.5,-1)(2.5,1)
\psline[linewidth=.5pt](-2.5,0)(2.55,0) % x-axis
\psline[linewidth=.5pt](0,-1)(0,1) % y-axis
\psplot[plotpoints=300]{-2.5}{.133}
{3 x 2 exp mul 2 x mul sub 15 x mul 2 sub div}
\psplot[plotpoints=300]{.134}{2.5}
{3 x 2 exp mul 2 x mul sub 15 x mul 2 sub div}
\end{pspicture}
\end{document}
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Run LaTeX here

However, before the style package can even attempt to load, I get an error message regarding the very first line:

! LaTex Error: Two \documentclass or \documentstyle commands

The confusion is that I've used this in the preamble before and it works perfectly fine. It is only in conjunction with the attempted pst-plot package that this arises. Can someone please explain?

Any feedback would be most appreciated. Thanks!

[Keta]

I get no errors with the code above

[Stefan Kottwitz]

I can confirm that this code is compilable without errors.
Perhaps post your log file as attachment here.

Stefan

[workerbee]

Sure. Here's the log file.

[Stefan Kottwitz]

I can see that the name of your file is pstricks.tex, that's causing the problem. pstricks.sty loads a file pstricks.tex by \input and finds your file instead of that of the package.
Just rename your tex file.

Stefan

[workerbee]

Thanks, Stefan.

I was able to get past that error and ran into another one. Apparently it's got a problem with the line: \psline[linewidth=.5pt]...

The coding is exactly the same as earlier, with a new file name; "using-tricks".

Here was the error message:

Code: Select all

1
2
3
4
5
6
7
8
9
10
11
! Undefined control sequence.
<recently read> \c@lor@to@ps 
                             
l.10 \psline[linewidth=.5pt](
                             -2.5,0)(2.55,0) % x-axis
? h
The control sequence at the end of the top line
of your error message was never \def'ed. If you have
misspelled it (e.g., `\hobx'), type `I' and the correct
spelling (e.g., `I\hbox'). Otherwise just continue,
and I'll forget about whatever was undefined.
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

[Stefan Kottwitz]

That's because you are using pdfLaTeX, use LaTeX instead. That means, compile to dvi and use dvips to produce a postscript file. If you finally want to get pdf output, use ps2pdf afterwards.

Stefan

[localghost]

To avoid more trouble take a look at the list of frequently done errors on the PSTricks homepage.


Best regards
Thorsten

[workerbee]

Thanks, Stefan. It worked!