Page Layout ⇒ geometry | Margins not set as specified

[seroland86]

I am using the geometry package to set margins of my document. Unfortunately the given values are not being implemented as expected. What I need is the following:

left margin: 4.0cm
right margin: 2.0cm
top margin: 2.5cm
bottom margin: 1.0cm

Finally I got it working but with totally different values in the definition. Can somebody explain why this is and give a proper solution so that I can put the values from above into the definition and the outputs really is like that?

Here is my document:

Code: Select all

Code, edit and compile here:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
\documentclass[11pt,a4paper]{article}
\usepackage[utf8]{inputenc}
\usepackage[ngerman]{babel}
\usepackage[T1]{fontenc}
\usepackage{lmodern}
\usepackage{graphicx}
\usepackage{microtype}
\usepackage[printonlyused]{acronym}
\usepackage{fancyhdr}
\usepackage{lipsum}
\usepackage[nottoc,numbib]{tocbibind}
\usepackage{geometry}
\geometry
{
    top=15.5mm,
    bottom=30mm,
    left=35mm,
    right=25mm,
    headsep=5.5mm,
    footskip=10mm
}
% include metadata
\input{srkssa_meta}
% header definition
\setlength{\headheight}{15.5mm}
\pagestyle{fancy}
\fancyhf{}
\lhead{\fontsize{10}{10} \selectfont \ThesisTitle}
\rfoot{\fontsize{10}{10} \selectfont \thepage}
\begin{document}
% start trailer
\thispagestyle{empty}
\input{srkssa_titlepage}    % titlepage
\newpage
\pagenumbering{roman}
\setcounter{page}{2}
\addcontentsline{toc}{section}{Eidesstattliche Erklärung}
\input{srkssa_auo}          % assertion under oath
\newpage
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Run LaTeX here

Thanks in advance!

Sebastian

[localghost]

For setting up the specified margins you should take some important things into account.

• Are the header and footer part of the text body or are they to be shifted into the vertical margins (top and bottom)?
• Is a binding correction (or binding offset) for the inner margin (left margin in a one-sided document) to be regarded?
• Does the problem occur only in the printed document?

I have no problem with the desired margins if I include the header and footer into the text body (see below).

Code: Select all

Code, edit and compile here:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
\documentclass[11pt,a4paper,ngerman]{article}
\usepackage[T1]{fontenc}
\usepackage{selinput}
\SelectInputMappings{
  adieresis={ä},
  germandbls={ß},
  Euro={€}
}
\usepackage{babel}
\usepackage{geometry}
\geometry{
  top=25mm,
  bottom=10mm,
  left=40mm,
  right=20mm,
  includeheadfoot,
  headsep=5.5mm,
  footskip=10mm
}
\usepackage{fancyhdr}
\usepackage{lmodern}
\usepackage[babel]{microtype}
\usepackage{blindtext}
\pagestyle{fancy}
\fancyhf{}
\lhead{\small Thesis Title}
\rfoot{\small \thepage}
\begin{document}
  \blinddocument
\end{document}
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Run LaTeX here

Finally your declaration of \headheight could be a bit problematic. For details about the geometry package you should consult its manual.

By the way, this is a very strange type area. Does not look very professional.


Best regards and welcome to the board
Thorsten