General ⇒ pbox package error: Undefined control sequence

[alanq]

(German Help - Hilfe auf deutsch: Undefined control sequence - wie finde ich heraus, was fehlt? - LC editor remark)

I'm trying to include newlines inside a tabular environment.

Following StefanK's answer to this problem here:
http://tex.stackexchange.com/questions/ ... table-cell
I tried the pbox package http://www.ctan.org/pkg/pbox.

But I get an 'Undefined control sequence' error.

MWE:

Code: Select all

Code, edit and compile here:

1
2
3
4
5
6
7
8
9
10
11
\documentclass[a4paper,10pt]{article}
\usepackage{calc}
\usepackage{ifthen}
\usepackage{pbox}
\begin{document}
\pbox{2cm}{one two three}
\end{document}
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Run LaTeX here

Error message:

Code: Select all

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
$ latex spr.tex 
This is pdfTeX, Version 3.1415926-1.40.10 (TeX Live 2009/Debian)
entering extended mode
(./spr.tex
LaTeX2e <2009/09/24>
Babel <v3.8l> and hyphenation patterns for english, usenglishmax, dumylang, noh
yphenation, ukenglish, loaded.
(/usr/share/texmf-texlive/tex/latex/base/article.cls
Document Class: article 2007/10/19 v1.4h Standard LaTeX document class
(/usr/share/texmf-texlive/tex/latex/base/size10.clo))
(/usr/share/texmf-texlive/tex/latex/tools/calc.sty)
(/usr/share/texmf-texlive/tex/latex/base/ifthen.sty)
(/usr/share/texmf-texlive/tex/latex/pbox/pbox.sty) (./spr.aux)
! Undefined control sequence.
\pb@xiii  ...1]{\pb@xlen }{#2}\ifthenelse {\equal 
                                                  {\pb@xargi }{}} {\parbox {...
l.12 \pbox{2cm}{one two three}
                              
? 
Underfull \hbox (badness 10000) in paragraph at lines 12--12
[]\OT1/cmr/m/n/10 one two
Underfull \hbox (badness 10000) in paragraph at lines 12--12
[]\OT1/cmr/m/n/10 one two
[1] (./spr.aux) )
Output written on spr.dvi (1 page, 292 bytes).
Transcript written on spr.log.
$
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

A <Return> after the ? yields the underfull hbox errors and output is produced.
Interestingly, the output file has TWO boxes side-by-side containing "one two three".

If the content of the pbox is shorter than the max width (2cm)
eg

Code: Select all

1
\pbox{2cm}{one two}
 
 
הההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההההה
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

there is no error, and the output is correct.

According to the documentation (http://mirror.ctan.org/macros/latex/con ... x/pbox.pdf), pbox requires the calc and ifthen packages, which I have included. But, commenting them out gives the same error and the same results!

[josephwright]

For me the example compiled perfectly (with TeX Live 2012). I suspect this is a version problem. You log indicates TeX Live 2009, while the latest release of pbox was in 2011. I suggest you download pbox from CTAN and install the file locally.

[alanq]

Thank you, Joseph [Sorry for the delay in replying]

I found that simply embedding another tabular environment works.
I'll upgrade pbox and use that if my scripts get too messy.

Cheers
Alan