General

Pepe93 · Post by **Pepe93** » Wed Apr 18, 2007 7:47 pm

And also with the correct page size 8O

[just kidding] well, then I may send you the content and you can finish writing my thesis ha ha ha[/just kidding]

ok, seriously, I will check for any possible mistakes. And I am also updating and re-installing the Miktex.

NEW: TikZ book now 40% off at Amazon.com for a short time.

And: Currently, Packt sells ebooks for $4.99 each if you buy 5 of their over 1000 ebooks. If you choose only a single one, $9.99. How about combining 3 LaTeX books with Python, gnuplot, mathplotlib, Matlab, ChatGPT or other AI books? Epub and PDF. Bundle (3 books, add more for higher discount): https://packt.link/MDH5p

Pepe93 · Post by **Pepe93** » Wed Apr 18, 2007 8:04 pm

ok, after updating, re-installing the MikTex, I can create PDFs, but I still have the page size problem

roman · Post by **roman** » Wed Apr 18, 2007 8:16 pm

The page size of my test document was correct. Adobe Acrobat Reader says 6.74 x 9.44 in ==> 171.196 x 239.776 mm.

Pepe93 · Post by **Pepe93** » Wed Apr 18, 2007 8:30 pm

Ok, I also tried in taking out the last content (just to see whether the problem was in the text etc) but the page size problem remains. Could it be due to the "unmatched Document" in the parse window?
This problem still remains and I can only get rid of it by quoting out the "\end{document}" line in the main file.
But then, of course, Latex will (emergency) stop the compilation

Pepe93 · Post by **Pepe93** » Wed Apr 18, 2007 9:10 pm

This seems to be a never ending story. I just quotet some other content files out, to test whether the page size is corrected and after placing them back in again. It was still not working.
I also tried re-installing TeXnicCenter, but now I have to re-define the profiles.
What should be the commands for just the "Pure" DVI to PDF using dvipdfm or dvipdfmx???

I get all the time this error for all the eps-images in the document (see image).

The problem with the unmatched document still remains...

peredur · Post by **peredur** » Tue May 17, 2011 12:19 pm

I know this is very old, but I'd been having similar problems (if you can call them that). I'm using TeXnicCenter 1.0 stable RC1 on WinXP Pro SP3.

There were two symptoms, reported by the parser:

An unmatched \end{document}
An unfound .idx file

Everything seemed to work OK in that a valid output file was produced. It just irritated my autistic tendency, especially since I knew the parse tree was valid.

In the end I just created an empty .idx file with the correct name. Everything now works. The parser reports nothing except that it's produced a file. The .idx file is still empty.

Bug in the parser? Permissions problem trying to create the file?

BTW, I only just found TeXnicCentre. Is it still being developed? Version 2 seems to have been in Alpha for a long time.

Hope this info is useful, anyway

Peredur

LaTeX.org

General ⇒ What is the purpose of Find 1, Find 2 and Parse Tabs in Outp

Re: What is the purpose of Find 1, Find 2 and Parse Tabs in Outp

Re: What is the purpose of Find 1, Find 2 and Parse Tabs in Outp

Re: What is the purpose of Find 1, Find 2 and Parse Tabs in Outp

Re: What is the purpose of Find 1, Find 2 and Parse Tabs in Outp

Re: What is the purpose of Find 1, Find 2 and Parse Tabs in Outp

What is the purpose of Find 1, Find 2 and Parse Tabs in Outp