Graphics, Figures & Tables ⇒ two figures vertical align

[Bahurin]

Hello to all. I have one problem. I prepared document with two independent figures:

Code: Select all

\documentclass[a4paper,12pt]{report} 
\usepackage[T2A]{fontenc}
\usepackage[utf8]{inputenc}
\usepackage[english,russian]{babel}
\usepackage{amssymb,amsfonts,amsmath,mathtext,cite,enumerate,float} 
\usepackage[dvips]{graphicx}

\usepackage{color}

\usepackage{geometry} 	
\geometry{left=2cm}		
\geometry{right=1.5cm}	
\geometry{top=1cm}		
\geometry{bottom=2cm}	


\usepackage{tikz}
\usepackage{pgfplots}
\pgfplotsset{width=8cm, height = 6cm}



\begin{document}

\begin{figure}[hr]
\begin{center}
\begin{tikzpicture}
\begin{axis}
\addplot coordinates {
( 338.1, 266.45 )
( 169.1, 143.43 )
( 84.5, 64.80 )
( 42.3, 34.19 )
( 21.1, 9.47 )};
\end{axis}
\end{tikzpicture}
\caption{Figure1}
\end{center}
\end{figure}

\begin{figure}[hr]
\begin{center}
\begin{tikzpicture}
\begin{axis}[ylabel = {$y(x)$}]
\addplot coordinates {
( 338.1, 266.45 )
( 169.1, 143.43 )
( 84.5, 64.80 )
( 42.3, 34.19 )
( 21.1, 9.47 )};
\end{axis}
\end{tikzpicture}
\caption{Figure2}
\end{center}
\end{figure}


\end{document}

but I got vertical shift between figures (see attached figure)

shift.png (13.84 KiB) Viewed 9712 times

How can I get vertical align both figures?

[tom]

Hi!

The figures are misaligned because of the labeled axis in the second figure which makes it wider than the first. The easiest solution is to label both y-axes. You can make the label of the first plot invisible if necessary.

Code: Select all

\begin{axis}[ylabel = \phantom{{$y(x)$}}]
...
\end{axis}

Also, you might want to use subcaption/subfig for a better control of the alignment and captions.

[cgnieder]

Hi Bahurin,

Welcome to the LaTeX community!

Probably the easiest here is to add trim axis left as option to the tikzpictures:

Code: Select all

\begin{figure}[h]
  \centering
  \begin{tikzpicture}[trim axis left]
    \begin{axis}
      \addplot coordinates {
        ( 338.1, 266.45 )
        ( 169.1, 143.43 )
        ( 84.5, 64.80 )
        ( 42.3, 34.19 )
        ( 21.1, 9.47 )
      };
    \end{axis}
  \end{tikzpicture}
  \caption{Figure1}
\end{figure}

\begin{figure}[h]
  \centering
  \begin{tikzpicture}[trim axis left]
    \begin{axis}[ylabel = {$y(x)$}]
      \addplot coordinates {
        ( 338.1, 266.45 )
        ( 169.1, 143.43 )
        ( 84.5, 64.80 )
        ( 42.3, 34.19 )
        ( 21.1, 9.47 )
      };
    \end{axis}
  \end{tikzpicture}
  \caption{Figure2}
\end{figure}

A few additional remarks:

• There is no float specifier r...
• I wouldn't use the {center} environment inside of the {figure} environment since it adds additional verticale whitespace above and below. \centering will work fine instead.
• \usepackage[dvips]{graphicx} it's better to leave the dvips option out and let graphicx figure out the needed driver itself.
• \usepackage{color} this package is superseded by xcolor. Since the TikZ package already loads xcolor you can remove that line completely

Regards

[Bahurin]

Hi Bahurin,

Welcome to the LaTeX community!

Probably the easiest here is to add trim axis left as option to the tikzpictures

Thank you very much for your advices. It is working correct now, but I have additional question.
Y label font decreases if I set ylabel as fraction. For example
\begin{axis}[ylabel = {$\frac{y(x)}{z(x)}$}]
How can I set normal font size for ylabel and keep vertical figures align in the same time?

2) Figures are not visible if I remove \usepackage{color}.